หัวข้อ: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: saimai 011 ที่ 26 สิงหาคม 2011, 09:31:28 พอดีรู้ข้อมูลมาว่ามันปรับกำลังส่งได้ อะครับ อยากลองปลับดูครับ ว่ามันจะแรงจริงปล่าว แล้วถ้าปรับไปแล้ว มันจะมีผลอะไรไหมครับ อยากรู้ว่ามันจะปรับกำลังส่งอย่างไงครับ อยากรู้ข้อมูลครับ รบกวนพี่ๆที่รู้วิธิปรับด้วยครับ
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: saimai 011 ที่ 29 สิงหาคม 2011, 13:05:29 อัพครับไม่มีใครรู้เลยหลอนี้
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: HSOWPB-001 ที่ 29 สิงหาคม 2011, 14:16:20 pm ให้เเล้วครับ
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: e27eaz ที่ 09 กันยายน 2011, 19:53:15 หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: toon055 ที่ 09 กันยายน 2011, 19:55:18 ขอด้วยครับผม หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: ord6859 ที่ 11 กันยายน 2011, 11:35:26 ขอด้วยคนครับ ขอบคุณล่วงหน้าครับ
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: cap231 ที่ 18 กันยายน 2011, 14:50:16 ขอด้วยครับขอบคุณครับ
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: misu793 ที่ 18 กันยายน 2011, 14:52:59 ผมก็ใช้รุ่นนี้ ขอด้วยคนครับ ขอบพระคุณล่วงหน้า
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: HS5DGC ที่ 18 กันยายน 2011, 14:55:52 ใช้เมนูลับของ9012เลยครับ อันเดียวกัน พิมในกูเกิ้ลตามสีเขียวเลยครับ ;D ;D ;D
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: ton_999 ที่ 19 กันยายน 2011, 21:39:14 ใช้เมนูลับของ9012เลยครับ อันเดียวกัน พิมในกูเกิ้ลตามสีเขียวเลยครับ ;D ;D ;D ถูกต้องคับผม แบบนี้คับ เปิดเมนู YAESU FM-9012 YAESU FM-9012 1.เปลี่ยนปุ่ม Wires เป็นปุ่มฟังก์ชั่นใดก็ได้ตามใจเรา ปุ่ม Wires คือปุ่มซ้ายมือสุด สำหรับเข้าระบบ Internet ตามที่ YAESU กล่าวอ้างไว้ สำหรับประเทศไทยคงไม่มี Server ระบบ Wires รองรับ ในขณะนี้ เราสามารถโปรแกรมปุ่มนี้เพื่อใช้ประโยชน์อย่างอื่นดังนี้ 1.1 ปิดเครื่อง>>แล้วกดปุ่ม Wires ค้างไว้>>แล้วเปิดเครื่องขึ้นมา จะได้ยินเสียงโทนแปลกๆ หู ตอนนี้ปุ่ม Wires กลายเป็นปุ่มที่ใช้ดูระดับแรงดันไฟฟ้า DC Volt ในเครื่องแล้ว 1.2 ท่านสามารถโปรแกรมปุ่มนี้ให้ทำงานอื่นโดยในขณะที่เข้า SET MODE เมื่อเลือก SET MENU ที่ต้องการโปรแกรม ให้กดปุ่ม Wires ค้างไว้ ต่อไปท่านสามารถเข้า SET MENU นั้นๆ โดยการกดปุ่ม Wires ได้ทันที (โดยวิธีเดียวกันนี้เหมือนกับการโปรแกรมปุ่ม P1-P4 บนไมค์นั่นเอง) 1.3 จะเอาปุ่ม Wires กลับมาทำงานในหน้าที่เดิมก็ทำขั้นตอนที่ 1.1 ซ้ำ 2. ทดสอบจอแสดงผล ทดสอบจอแสดงผลว่ามีบอดตรงไหนหรือเปล่าโดย ปิดเครื่อง>>กดปุ่ม SET>>แล้วเปิดเครื่องขึ้นมา หน้าจอจะแสดงผลทุกตัวอักษรพร้อมกัน ไม่ต้องตกใจ ปิดเครื่องเปิดใหม่ตามปกติก็หาย 3. ทีเด็ด !!! เข้า Service Menu คำเตือน !!! หากไม่แน่ใจอย่าเล่น ใช้สติและความรอบคอบ หมั่นสังเกตและจดจำ ขอรับรองว่าผมทดสอบแล้วว่าที่จะกล่าวต่อไปนี้สามารถทำงานได้จริง และขอยืนยันว่าเครื่องที่ออกมาจากโรงงานได้ผ่านการปรับแต่งจากเครื่องมือราคาแพงมากและมีประสิทธิภาพมาก ดังนั้นในการใช้งานปกติไม่จำเป็นต้องปรับแต่งอื่นใดอีก 3.1 ปรับให้เครื่องมาอยู่ที่ VFO Mode 3.2 ปิดเครื่อง>>กดปุ่ม DW+MW>>แล้วเปิดเครื่องขึ้นมา จะสังเกตว่าสเควลช์เปิดมีเสียงดังซู่ (ทั้งๆ ที่ก่อนหน้านี้เราทำให้เงียบแล้ว) และจะมีตัวอักษรแปลกๆ ในตำแหน่งที่แสดงเลข Memory นั่นคือตอนนี้เข้า Service Mode แล้ว ( 555 ดีใจด้วย) ข้างล่างนี้คือเมนูของ Service Mode RF ... Frequency adjust TN ... Receiver sensitivity tuning TL ... Trigger Level (squelch adjust) S1 ... S-Meter low threshold S9 ... S-Meter high calibration HP ... 50 watt power adjust L3 ... 25 watt power adjust L2 ... 10 watt power adjust L1 ... 5 watt power adjust DV ... Deviation Adjust (DTMF/Voice) 100 ... CTCSS level adjust DC ... DCS level adjust. 3.3 ก่อนอื่นเลยให้จดค่าตั้งต้นเก็บไว้ก่อนโดยหมนุลูกบิดเลือกแต่ละเมนูแล้วกดปุ่ม MW เพื่อเข้าไปดูค่า และกด MW อีกครั้งเพื่อกลับออกมาและเลือกดูค่าอื่นต่อไป นี่ เมนู ค่าตั้งต้น ความหมาย ******ตัวสีแดง อันตรายคับ อย่าไปยุ่งกับค่าของมันคับ(การตั้งค่าเครื่องแต่ละเครื่องไม่เหมือนกันขึ้นอยู่กับเครื่องนั้นๆ)****** RF ... Frequency adjust 5d ปรับความเที่ยงตรงความถี่ภาครับ TN ... Receiver sensitivity tuning 08+ ปรับความไวภาครับ TL ... Trigger Level (squelch adjust) 5C ระดับความแรงสัญญาณที่จะเปิดสเควลช์ S1 ... S-Meter low threshold 28 ความแรงสัญญาณที่ S-meter ระดับ 1 S9 ... S-Meter high calibration 40 ความแรงสัญญาณที่ S-meter ระดับ 9 HP ... 50 watt power adjust E2 ความแรงภาคส่งตำแหน่ง High L3 ... 25 watt power adjust A7 ความแรงภาคส่งตำแหน่ง Low3 L2 ... 10 watt power adjust 73 ความแรงภาคส่งตำแหน่ง Low2 L1 ... 5 watt power adjust 54 ความแรงภาคส่งตำแหน่ง Low1 DV ... Deviation Adjust (DTMF/Voice) 9E การเบี่ยงเบนทางความถี่ภาคส่ง 100 ... CTCSS level adjust 5C ระดับความแรงสัญญาณ CTCSS DC ... DCS level adjust. AC ระดับความแรงสัญญาณ DCS การเข้าไปเปลี่ยนก็กดปุ่ม MW เข้าตัวเลือกที่ต้องการแล้วหมุนลูกบิดเพื่อเปลี่ยนค่า กด MW อีกครั้งเพื่อกลับออกมาเลือกตัวเลือกอื่น เมื่อเปลี่ยนทุอย่างจนพอใจแล้วให้กดปุ่ม DW เพื่อบันทึกค่าที่แก้ไขไป 4. ปิดแบนด์..... ปิดเครื่อง ------ กดปุ่ม WIRE + SET พร้อมกัน >> หน้าจอขึ้น ALL RESET กดปุ่ม MW -------- แหล่งข้อมูลจาก http://groups.yahoo.com/ The Yaesu FT-1802 is a 50watt 2 meter FM rig with some very interesting software mods anyone can perform. Additionaly there is a service menu that can be used to fine tune the radio... but with caution. 1) The "My Key" mod... If you don't have a Wires host in your area you can still make use of the Wires button (the one with the atom symbol on it) on the front of the radio. Turn your radio off from the front of the radio, hold the wires key down while you turn the radio back on. When the frequency display comes back on the button is transformed into a programmable soft key like the ones on the Mic. By default pressing it will display the internal voltmeter. If you go into SET mode pressing the wires key for 2 seconds will program it to whatever menu function is currently selected. (I use mine for the RF squelch) To undo this repeat the procedure. 2) 2 meter only receive Turn your radio off. Press and hold the Wires and SET buttons while you turn the radio back on. This will display the ALL RESET message. Pressing MW will reset the radio. Turn it off and back on and your receiver is restricted to 144 to 148 mhz. You will have to reprogram your radio. If you are using the computer software for this anything outside the 2 meter band will produce errors. To undo this repeat the procedure. 3) Display test Think you messed up your display? Press and hold the SET key while turning on the radio. It will come on with all display segments turned on. Turn the radio off and back on to resume normal operations. 4) Calibration (Service) Menu WARNING: You mess with this section at your own risk! To enter the service menu go to VFO mode, turn off your radio, press and hold the DW and MW keys while you turn it back on. When it comes on you will be in a service menu where the item selection is on the right of the display, where the memory channel number usually sits. The service items are: RF ... Frequency adjust TN ... Receiver sensitivity tuning TL ... Trigger Level (squelch adjust) S1 ... S-Meter low threshold S9 ... S-Meter high calibration HP ... 50 watt power adjust L3 ... 25 watt power adjust L2 ... 10 watt power adjust L1 ... 5 watt power adjust DV ... Deviation Adjust (DTMF/Voice) 100 ... CTCSS level adjust DL ... DCS level adjust. To select from the menu rotate the tuning knob. To see/set an item pres MW To adjust the item rotate the tuning knob. Press MW to return to select mode. Before you decide to tinker with any of this write down the original settings so you can restore them if needed. When done press DW to save the settings and restart the radio. To exit this menu without saving changes turn off the radio without pressing the DW button. Some "tone deaf" repeaters might benefit from a slight increase in the CTCSS levels (set to 15% at factory) and you might find that decreasing the Trigger Level makes the squelch control a lot more effective. หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: E20OQV ที่ 21 กันยายน 2011, 21:00:41 ;D ธรรมดามันก้อแรงอยู่แล้วคับ ปรับๆ ยิ่งแแรงเข้าไปใหญ่
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: HS5QHX ห้ามซื้อขาย จนกว่าจะเคลียร์เรื่องเก่าเรียบร้อย ที่ 21 กันยายน 2011, 21:02:17 ปรับมา พีเอทำงานหนัก เครื่องพัง จบข่าว เดิมๆก็ดีอยู่แล้ววววววววววว
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: E20OQV ที่ 21 กันยายน 2011, 21:10:14 ปรับมา พีเอทำงานหนัก เครื่องพัง จบข่าว เดิมๆก็ดีอยู่แล้ววววววววววว ถูกต้องคับ เดิมๆ แบบไม่ปรับ ส่ง QRO ต่อเนื่องแบบสบายๆ ไม่ต้องเหวอครับ หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: hs3kvx(ทศ) ที่ 21 กันยายน 2011, 21:13:05 พี่เดิม ๆ มันก็แรงแล้วครับ จะจัดให้แรงกว่านี้ทำไมครับ ผมยังอยากหาวิธีปรับลดกำลังส่งอยู่เลยทุกวันนี้ใช้งานก็ใช้แ่ต่โลครับ
หัวข้อ: Re: อยากเพื่มกำลังส่งของ ยาสุ 2900 ทำไงดี เริ่มหัวข้อโดย: kengzaza1 ที่ 21 กันยายน 2011, 21:57:35 ขอPM ด้วยคนครับ Webmaster Earn Money! By Affiliate Program 100% Pay www.samuismile.com |